#TutorialTuesday: Sora Cosplay Write-up

Happy Kingdom Hearts 3 launch, everybody!
We’ve waited SO long for this main story to continue – the last time I was really into Kingdom Hearts was when I cosplayed Sora from Kingdom Hearts 2…10 YEARS AGO!!

with Tsubaki Costuming Australia Photo by Pireze

To celebrate this new installment, I’m going to make an epic 10-year throwback to my KH2 Sora cosplay and attempt to make a Sora tutorial for you.
(I say attempt because 10 years ago I didn’t really take work-in-progress pictures…so it’s going to be closer to a write-up than a step by step tutorial).

 

Photo by Pireze

Costume:
Breakdown: Standard pleather hoodie jacket cut short + standard inner shirt with a tummy pocket + a fat balloon pant with random shit stuck all over it. The giant zipper was made from EVA skin sheets, for the EXTRA GINORMOUS teeth. The shoulder pads were silver vinyl fabric trimmed with white bias tape.
The balloon pants were lined with heavy fabric to give it some mass. I left gaps in the lining to allow airflow, so the pants actually inflate like a balloon when I bend my legs which was pretty fucking cute.

Photo by Risachantag
Photo by Risachantag

Necklace and Buckles: all modeled from Sculpy oven bake clay.

Gloves: Nothing special here.I bought a pair of gloves and stuck belts and pads onto them.

Shoes: These were my pride and joy back then. I got a pair of CROCS, taped a massive amount of Hobby Fill to the front then covered the shoe with spandex for the big round look. Then I just stuck all the random zippers and belts onto them.

Wig: Before the time of quality wigs… I styled my Sora wig using a punky party wig. I just spent a night with a can of hairspray and a tube of got2be hair gel and a blow dryer. Completed in 5 hours. Destroyed by the wind at the beaches of Perth where we did our first photoshoot in 2 seconds.

Oathkeeper Keyblade:
First I drafted a stencil by hand onto several sheets of baking paper.
Then I transferred the stencil to sheet of 12mm ply wood and cut that shit out with a jigsaw. Then I ran a table router along all the edges to give it some beveled edges.  Further details and contours were then built on with DAS modelling clay, and sanded smooth once dry. Nowadays, a more lightweight and quicker drying option is foam clay from luminsworkshop.com.

The paupu fruit is a hand sewn plushy. The leaf that’s attached to it was a real leaf that I picked from my garden.

The paint job was done with several enamel spray paints. I chose a metallic sky blue for the center of the colourful detail to give it a much more elegant shine instead of the rather kindergarten colours that a dark blue gives off when applied next to yellow. The wings were done with a gradient of dusk gray and beige to enhance the smoothness of the feathers. I didn’t own an airbrush, so all the gradient effects were done by extremely careful spraying with the spray can that the paints came in.

Oblivion Keyblade:
First I drafted a stencil by hand onto several sheets of baking paper.
Then I transferred the stencil to sheet of 12mm ply wood and cut that shit out with a jigsaw. Then I ran a table router along all the edges to give it some beveled edges.
All details were molded on top with DAS air dry clay. Once again, foam clay from luminsworkshop.com would work now too.
I made the chain that runs down the middle of the keyblade out of oven bake clay.
For the painting, I mixed Metallic Grey and Black to give it realistic colour and weapon-like shine. The center gem was colored with silver with a layer of clear blue on top.

THAT’S IT! That’s how I made Sora 10 years ago.
I hope you enjoyed my Baby Wirru crafting and I hope it gives you some crafty ideas for your own cosplays. Happy KH3 launch~

Please support my ongoing supply of cosplay tutorials by either becoming a Patron on Patreon or purchasing a book from my Store.

Leave a Reply

Your email address will not be published. Required fields are marked *